Initialization key (reset)

Please open the back cover of the device, press and hold the RESET button, wait for two seconds until hear the prompt tone and then release it. The admin password will be restored to the factory default value(1234). If continue to press and hold RESET button for five seconds and disconnect the RESET button after hearing “Data Initializing”. At this time, the device will automatically initialize until prompt "Initialization Successful". The device will clear or restore all card data, fingerprint data, admin password and other data to factory defaults.

Management status command table:

Login management status: * + management password+#

The default management password is 1234. After logging in to the management status, the green indicator light becomes normally on.

Exit management status: **

After exiting the management state, the red indicator turns to flash.

Note: the following commands are only valid in management status. (in the management state, if there is no keyboard operation for 10 seconds, the fingerprint machine will automatically exit the management state)

1、 Card and Password Registration

Enter the card number to register the card: 10 + \\#

For example, if the card number is "0012345678", you only need to enter 12345678 (prompt tone: successful registration)

Password registration: 11 + \\4-8 digit password +#

Up to 100 groups of door opening passwords can be registered.

Duress password registration: 12 + \\4-8 digits duress password +#

There is only one set of duress passwords. The second registration will overwrite the previous set of passwords.

Swipe registration card: 20 + \\

You can swipe multiple cards continuously for registration. During registration, there will be a voice prompt: "please read the card" (when registration is successful, there will be a prompt tone: registration is successful)

Self numbered card issuing: 21 + \\read card + 3-digit self numbering + read another card + 3-digit self numbering.

It is convenient to remember. If a card is issued to Room 302 (self numbered 302), the card number corresponds to the room number, which is easy to remember. (one self numbering supports multiple cards) if you need to continuously add cards with self numbering, please continue to read the card after the 3-digit self numbering is entered and enter the self numbering.

Master card registration: 23 + \\

This card is only the master card after registration (Master card function: swiping the master card once will directly enter the card deletion fingerprint state, and swiping the master card twice in a row will directly enter the registration fingerprint state of the registration card)

Card + password registration: 24 + \\#

Use card + password to open the door: swipe the card and then enter the corresponding password to open the door.

2、 Delete Card Delete Password

Card swiping and deleting: 30 + \\

This method can continuously read multiple registered cards to delete cards in batch.

Card No. delete card: 31 + \\8-digit Card No. +#

If the card number is "0012345678", just enter "12345678" to delete it.

Deletion of self numbered card: 32 + \\3 digit number +#

After the operation is successful, all the 3-digit self numbered cards will be deleted.

Delete a single password: 35 + \\#

After the operation is successful, the corresponding password can be deleted.

Delete all passwords: 36 +#

All door opening passwords will be deleted.

Delete all door opening registration data: 40 +#

After successful operation, all registered cards, fingerprints and passwords will be deleted.

3、 Fingerprint Registration

Registered fingerprint: 28 + \\\n + input fingerprint + 1-9 digit number +#

When you press your finger to register your fingerprint, there will be a voice prompt: "please press your fingerprint". You need to press the fingerprint three times in a row. Each time you press the fingerprint, there will be a voice prompt: "please press the fingerprint again". After three fingerprint recordings, there will be a voice prompt: "please enter the number". This number can be used to output Wiegand signals.

Delete fingerprint: 38 + \\#

After the operation is successful, the corresponding fingerprint can be deleted.

4、 Set Prompt Voice

Modify voice: 50 +#

Switch between Mandarin and English.

5、 Modify Parameters

Modify administrator password: 60 + \\\new management password + \\repeat new management password +#

When changing a new management password, you need to change it to a 1-8 digit password and confirm the new password twice. When entering, the two passwords should be the same, otherwise it will not succeed.

Prompt for modifying door opening timeout: 63 + \\3-digit door opening timeout +#

If you enter 000, it will be set to 0.5 in seconds, and the maximum setting can be 999 seconds.

Modify alarm duration: 64 + \\3-bit alarm duration +#

If you enter 000, this function will be turned off. If you enter 255, the alarm duration is unlimited.

Modify the door opening delay time: 66 + \\3-bit door opening delay time +#

If 000 is set to 0.5 seconds, the system defaults to 3 seconds, and the maximum can be set to 255 seconds.

Anti detection door opening password setting: 68 + \\1-bit error times + 2-bit locking duration +#

After the setting is successful, if the number of input errors reaches the set value, the access control will be self locked, and the normal use will not be restored until the preset locking time is exceeded.

Set electric lock normally open: 83 +#

After the setting is successful, the electric lock remains normally open.

Set electric lock normally closed: 84 +#

After the setting is successful, the electric lock remains normally closed.

Restore factory settings: 70 +#

After successful operation, all data will be restored to the factory.

6、 Data Management (customized USB flash disk)

U disk download data: 91 +#

The device will download all the registered cards, fingerprints, passwords, access control and other data to the USB flash disk. After the download is successful, a voice prompt will appear: "USB flash disk synchronization is complete."

U disk uploading data: 92 +#

The device will upload the data in the USB flash disk to the device. After the upload is successful, there will be a voice prompt: "USB flash disk synchronization is complete."