Reset key (RESET)

Press and hold the reset button, wait for 2 seconds to hear the prompt tone (drop), and then release it. The access control will restore the management password to the factory default value (1234). If you continue to press and hold reset for 5 seconds, you can disconnect the reset button after hearing the initialization prompt tone (drop. Drop. Drop). At this time, the access control will automatically perform the initialization work until the end prompt tone is issued. Initialize the equipment, and all card data and management passwords are cleared or restored to factory default values. (delete all cards, restore all parameters, restore management password: 1234)

Management status command table:

Login management status: * + management password#

The default management password is 1234. After logging in to the management status, the green light (mode) turns on.

Exit management status:**

After exiting the management state, the green light (mode) will flash.

Note: the following commands are only valid in the management state. (in the management state, if there is no keyboard operation for 10 seconds, the program will automatically exit the management state)

1、 Issuing password

Card No.: 10 + # + 8-digit Card No+#

The card is printed with "0012345678", and the card can be issued as long as the last 8 digits are 12345678

Add door opening password: 11 + # + 4-8-digit door opening password+#

The door opening password is 4-8 digits. Up to 100 groups of door opening passwords can be added

Add coercion password: 12 + # + 4-8-bit coercion password+#

There is only one group of coercion passwords. When adding a new coercion password, the original group will be overwritten

Fast card issuing: 20 + # card reading

Multiple cards can be read continuously at the same time to add cards. If the card reading stops for 10 seconds, the program will automatically exit the management state

Self numbering card issuing: 21 + + card reading + 3-digit self numbering

For easy memory, if a card is sent to Room 302 for use (self numbered as 302), the card number corresponds to the room number, which is easy to remember. (one self numbering supports multiple cards) if you need to continuously add cards with self numbering, please enter # after the 3-digit self numbering is input, and then read the card again and issue the next card continuously

Add master card: 23 + # + read Master card

Master card adding: read the master card twice continuously and enter the master card adding mode. You can read the card continuously and issue cards,

Master card deletion: in the unmanaged state, read the master card once, enter the card deletion mode, read the card to be deleted twice in a row, and then read the master card again to confirm and delete the card uniformly

Card + password: 24 + # + card reading + input the 4-8-digit password of the card+#

After entering the command, read the card and then enter the password

2、 Delete card and password

Do not delete the card by swiping: 30 + # card reading

This method can read multiple registered cards for deletion at the same time. If the card is stopped for 10 seconds, the program will automatically exit the management state

Card number deletion: 31 + # 8-digit card number+#

If "0012345678" is printed on the card, the card can be deleted as long as the last 8 digits are 12345678.

Self numbered card deletion: 32 + # + 3-digit number+#

After input, the card corresponding to the 3-digit self number will be deleted.

Delete a single password; 35 # + door opening password+#

After entering, delete the corresponding door opening password

Delete all passwords: 36+#

All door opening passwords will be deleted

Delete all door opening data at once: 40+#

After the command is executed, the access control will clear the data such as the door opening card and the door opening password. After the data is cleared, the rear door is forbidden to send an end prompt sound, indicating completion.

3、 Modify parameters

Modify administrator password: 60 + # + 4-8 new administrator password + # + repeat 4-8 new administrator password+#

When replacing the new management password, you need to confirm the new password twice. When entering, the two passwords should be the same, otherwise it will not succeed

Modify the door opening timeout prompt: 63 + # + 3-bit door opening timeout+#

When 000 is entered, the door opening timeout prompt function will be closed. Set 255 seconds, indicating that the alarm is always on

Modify alarm duration: 64 + # + 3-bit alarm duration+#

When you enter 000 (default), the alarm is turned off. When you enter 255, the alarm time is not limited

Modify the door opening delay time: 66 + # + 3-bit door opening delay time+#

When you enter 000, it is set to 0.5 seconds, the default is 3 seconds, and the maximum is 255 seconds

Anti detection door opening password: 68 + # + 1-bit error times + 2-bit lock duration+#

When 999 is entered (default), if someone enters the wrong password 9 times, the access control will lock for 99 seconds.

4、 Factory recovery

Restore factory default: 70+#

After the command is input, all parameters are automatically restored to the factory default values. (delete all cards, restore all parameters, restore management password: 1234)

5、 Opening and closing commands (IC models do not have anti copy card interception function)

Set electric lock (normally open): 83+#

After successful setting, the electric lock will not be locked. (this function can also be started by pressing and holding the "exit switch" for 5 seconds.)

Set electric lock (normally off): 84+#

After the setting is successful, the default state will be restored. (this function can also be turned off by pressing and holding the "exit switch" for 5 seconds.)

Open full card door: 85+#

After this function is enabled, the door can be opened by reading all cards

Enable full card door opening + automatic registration: 86+#

After this function is enabled, all cards can be opened. If it is an unregistered card, register at the same time, and then open the door

Close the full card door; 87+#

Turn off the full card function mode

Enable anti duplication card function: 88+#

After the setting is successful, the system starts to intercept the copy card

Turn off the anti duplication card function: 89+#

After the setting is successful, the copy card can also open the door normally. (default)