RESET Button

Press and hold the RESET button, wait for 2 seconds, release it after hearing the prompt tone (drop), and the access control will restore the admin password to the factory default value (1234). If you continue to press and hold RESET for 5 seconds, you can disconnect the reset button after hearing the initialization prompt tone (drop. Drop. Drop). At this time, the access control will automatically carry out the initialization work until the end prompt tone is sent by the access control. The default values of all equipment initialization and admin are cleared. (delete all cards, restore all parameters, restore admin password: 1234)

Admin Status Command:

Login Admin State:  * + admin password #

Default admin password: 1234. After logging in the admin status, the green light (mode) will normally on.

Exit Admin State: **

After exiting the admin state, the green light (mode) will flash.

Notice: the following commands are valid only in the admin status. (In the admins status, if there is no operation on  keyboard with 10 seconds, the program will automatically exit the admin status. )

1, Issuing Card and Password

Issue card by card number: Enter 10 + # + 8 digits of card number + #

Generally, it has card number printed on the card, for example ""0012345678". You can issue the card just enter the last 8 digits "12345678".

Add door opening password:  Enter 11 + # + 4-8 digits of door opening password + #

The door opening password is 4-8 digits. Up to 100 groups of door opening passwords can be added.

Add duress password: Enter 12 + # + 4-8-digits of duress password+#

There is only one set of duress passwords, and the second registration will overwrite the previous set of passwords.

Quickly issue card: Enter 20 + # swipe card

Multiple cards can be read continuously at the same time to add cards. If the card reading stops for 10 seconds, the program will automatically exit the admin state.

Issue card by self number: Enter 21 + # +swipe card + 3 digits of self number

It is convenient for memory. If a card is issued to Room 302 (self numbered 302), the card number corresponds to the room number, which is easy to remember. (one self numbering supports multiple cards) if you need to continuously add cards with self numbering, please input # word keys after the 3-digit self numbering is completed to read the card and issue the next card continuously.

Add master card: Enter 23 + #+ swipe Master card

Master card adding: read the master card twice continuously and enter the master card adding mode. You can read the card continuously for card issuance,

Master card deletion: in the non admin state, read the master card once, enter the card deletion mode, read the card to be deleted twice in a row, and then read the master card again for confirmation to delete the card uniformly.

Card + password: Enter 24 + #+ swipe card + enter the 4-8 digits of password+#

After entering the command, please swipe card and then input the password.

 2, Delete Card and Password

Swipe card to delete card: Enter 30 + # + Swipe card

This method can continuously read multiple registered cards for deletion at the same time. If you stop reading the card for 10 seconds, the program will automatically exit the admin state.

Card number delete card: Enter 31 + # + 8 digits of card number + #

If "0012345678" is printed on the card, the card can be deleted as long as the last 8 digits 12345678 are input.

Self number delete card: Enter 32 + # + 3 digits of self-number + #

After input, the card corresponding to the 3-digit self numbering will be deleted.

Delete a single password: Enter 35 + # + door opening password + #

After entering, delete the corresponding door opening password.

Delete all passwords: Enter 36+#

All door opening passwords will be deleted.

Delete all opening data at one time: Enter 40 + #

After the command is executed, the access control will clear the door opening card, door opening password and other data. After clearing, the end prompt tone will be sent out to indicate completion.

3, Modify Parameters

Change admin password:  Enter 60 + # + 4-8 new admin password + # + repeat 4-8 new admin password + #

When replacing a new admin password, you need to confirm the new password twice. When entering, the two passwords should be the same, otherwise it will not succeed.

Modify the door opening timeout prompt: Enter 63 + # + 3 digits of door opening timeout + #

When you enter 000, turn off the door opening timeout prompt function. Set 255 seconds to indicate that the alarm is always reported.

Modify alarm duration: Enter 64 + # + 3 digits of alarm duration + #

Enter 000 (default), the alarm is turned off. If enter 255, the alarm time is unlimited.

Modify the door opening delay time: Enter 66 + #+ 3 digits of door opening delay time + #

When you enter 000, it is set to 0.5 seconds, the default is 3 seconds, and the maximum is 255 seconds.

Anti-detecting password: Enter 68 + # + 1 digit of error times + 2 digits of locking duration + #

When entering 999 (default), if someone enters the wrong password 9 times, the access control will be self-locking for 99 seconds.

4, Restore Factory

Restore factory default: Enter 70 + #

After the command is entered, all parameters will automatically return to the factory default values. (delete all cards, restore all parameters, restore admin password: 1234)

5, Opening and Closing Commands (Mifare models do not sipport anti-copy card function)

Set electric lock normally open: Enter 83+#

After the setting is successful, the electric lock will not be locked. (this function can also be started by long pressing the "door out switch" for 5 seconds)

Setting electric lock normally closed: Enter 84+#

After setting successfully, restore the default state. (this function can also be turned off by pressing and holding the "exit switch" for 5 seconds)

Enable the full card opening: Enter 85+#

When this function is turned on, the door can be opened by reading all cards.

Enable the full card opening + auto registration: Enter 86+#

After this function is turned on, all cards can be opened. If it is an unregistered card, register at the same time, and then open the door.

Disable the full card opening: Enter 87+#

Turn off the full card function mode.

Enable the copy card function: Enter 88+#

After the setting is successful, the system starts to intercept the copy card.

Disable the copy card function: Enter 89 + #

After the setting is successful, the copy card can also open the door normally. (default)